PRODUCTS / AMERICAN / EUROPEAN BRAND SPECIALIZED TOOLS / HARLEY-DAVIDSON（100）
| Model | 14-K1013 |
| Item Name | Balancer Bearing Service Tool Kit |
| Descriptions | Ideal tool to remove and install outer balancer bearing on the chain guide support plate safely.<br> Also installs the new balancer bearing and counter balancer shaft on Twin Cam 96 or 110 B Softail engines.<br> <br> Fits 2007 to Present FXST.<br> Taiwan Pat.<br> |
Inquire Now
| Model | 14-K1014 |
| Item Name | Ignition Switch Connector Remover Tool |
| Descriptions | Ideal tool to remove the ignition switch wiring connector.<br> <br> Fits FL Touring models on 2003 to 2013 that have a H-D No.61530-03B Ignition Switch.<br> |
| Model | 14-K1015 |
| Item Name | Top Dead Center Tool |
| Descriptions | Fits: All Sportster Motors, All Big Twins |
| Model | 14-K1016 |
| Item Name | Oil Pump Seal Installer |
| Descriptions | Ideal tool to install oil pump seal below gear surface for a no-leak fit.<br> <br> Fits all Big Twin aluminum oil pumps 1968-Present. (except Twin Cam).<br> |
| Model | 14-K1017 |
| Item Name | Rocker Box Alignment Tool Set |
| Descriptions | Idea tool screw to allow precise alignment of twin cam rocker boxes to avoid improper sealing surface issues and rocker arm interference problems.<br> <br> Fits any Twin Cam Rocker Box Covers from 1999 to present. |
| Model | 14-K1018 |
| Item Name | Wrist Pin Lock Ring Tool |
| Descriptions | Ideal tool to install spiral-lock type wrist pins without distorting ring.<br> <br> Fits wrist pin size 0.515 inch inner diameter.<br> |
| Model | 14-K1018A |
| Item Name | Wrist Pin Lock Ring Tool |
| Descriptions | Ideal tool to install spiral-lock type wrist pins without distorting ring.<br> <br> Fits wrist pin size 0.535 inch inner diameter.<br> |
| Model | 14-K1019 |
| Item Name | Hollow Axle Plug Tool |
| Descriptions | Ideal tool to align rear axles, providing the correct center point required for safe vehicle alignment. <br> Lube the O-ring ends and insert in left to right ends of the axle.<br> <br> Fits 2008 to present hollow rear axle model Sportsters, Dyna, and Softail.<br> |
| Model | 14-K1020 |
| Item Name | Hose Repair Kit |
| Descriptions | Hose barbed end is .3125 (5/16”), thread end is 12mm x 1.25. It can be used with either a .250” or .3125” hose.<br> <br> Fits all the 12mm spark plug threads on all Twin Cams, XL 1986 and later, as well as Screamin’ Eagle EVO BT heads.<br> |
| Model | 14-K1021 |
| Item Name | Crankshaft Bushing Remover/Installer Tool |
| Descriptions | Ideal tool to remove and install the crankshaft bushing in the support plate on a Twin Cam. <br> Fits on all twin cam.<br> |
| Model | 14-K1022 |
| Item Name | 6-Speed Main Drive Gear Bearing Tool |
| Descriptions | Ideal tool to install the two bearings and seal in the main drive gear.<br> <br> Fits all 2006 to present Dyna and 2007 to present FL & FXST.<br> |
| Model | 14-K1023 |
| Item Name | Magnetic Tappet Holder Tool Set |
| Descriptions | Ideal tool to hold the tappets in the tappet bores when changing or servicing cams.<br> <br> Magnets will magnetically hold the tappet in place while performing any cam chest work when installing the tool over the tappet cover, a time saver tool.<br> <br> Fits Harley-Davidson Twin Cam and Milwaukee Eight engines.<br> |
| Model | 14-K1024 |
| Item Name | Piston Pin Bushing Tool Set |
| Descriptions | Ideal tool to remove and install wrist pin bushing without removing rods from crankcase.<br> <br> Fits Harley-Davidson all Twin Cam 1999-2006.<br> |
| Model | 14-K1025 |
| Item Name | Balancer Shaft Bearing Remover and Installer Set |
| Descriptions | Ideal tool to remove and install Balancer Shaft Bearings.<br> <br> Fits Harley-Davidson all Twin Cam 88™ Balanced Engines.<br> |
| Model | 14-K1026 |
| Item Name | Valve Spring Compressor Tool Set |
| Descriptions | Ideal tool set to compress valve springs for removal or installation. Included collars for Conical Valve Springs and Milwaukee Eight Valve Spring. <br> <br> Fit most Big Twin and XL models, new Milwaukee Eight series engine. |
| Model | 14-K1027A |
| Item Name | 10mm/12mm Cylinder Head Holding Tool |
| Descriptions | Ideal tool to hold the cylinder head that you are servicing.</br> The 12mm end is for Twin Cam two valve heads while the 10mm end is for Milwaukee Eight four valve heads.</br> </br> Fits both Twin Cam and Milwaukee Eight cylinders. |
| Model | 14-K1027B |
| Item Name | 12mm/14mm Cylinder Head Holding Tool |
| Descriptions | Ideal tool to hold the cylinder head that you are servicing.</br> </br> Fits H.D. 1948-2013 |
NEW
| Model | 14-K1033 |
| Item Name | Oil Filter Wrench |
| Descriptions | Fits '21-later Revolution Max engine-equipped models. |
| Model | 14-K395 |
| Item Name | Wheel Bearing Removal/Installation Tool |
| Descriptions | It can be used on 3/4＂and 1＂I.D. bearings 2000-2006 and 25mm bearings on most 2007-2008 models with or without ABS. |
| Model | 14-K440D |
| Item Name | Generic Shock Adjusting Tool＜For Harley-Davidson＞ |
| Descriptions | Applications :<br> Sportster models from 1967-1974, all Sportster and FXR models from 1982 to present, and all 4-speed FL and FX models from 1958-1986.<br> |