NEW PRODUCTS
NEW
| Model | 14-K1033 |
| Item Name | Oil Filter Wrench |
| Descriptions | Fits '21-later Revolution Max engine-equipped models. |
Inquire NowNEW
| Model | 14-K496A |
| Item Name | 10 & 12mm Top Dead Centre Tool |
| Descriptions | Fits 10mm or 12mm spark plug holes.<br> Material : Stainless 304<br> |
NEW
| Model | 14-K632B |
| Item Name | Combo Nitrogen Needle Kit |
| Descriptions | Used to fill shocks with self-sealing type rubber valve.<br> |
NEW
| Model | 14-K819K |
| Item Name | Shaft Holding Tool |
| Descriptions | It can hold shock shafts, fork cartridges, damping rods or other round shafts while servicing.<br> Size: 31mm.<br> |
NEW
| Model | 14-K876 |
| Item Name | Shock Needle Tool＜For KTM＞ |
| Descriptions | Used to replace the compression needle from the shock body on WP PDS shocks.<br> It have two locator washers that allow the tool to rest inside the shock body and not get skewed while tightening or loosening the compression metering pin.<br> Fits KTM most WP PDS shocks models.<br> |
NEW
| Model | 14-K887 |
| Item Name | Rotor Holding Tool＜For Kawasaki＞ |
| Descriptions | Fits 2006-2009 Vulcan 900 classic, classic LT and custom. |
NEW
| Model | 14-K887A |
| Item Name | Rotor Holding Tool＜For Kawasaki＞ |
| Descriptions | Fits 2006-2009 Vulcan 900 classic, classic LT and custom. |
NEW
| Model | 14-K890 |
| Item Name | Timing Sprocket Nut Tool＜For Moto Guzzi＞ |
| Descriptions | For crankshaft timing sprocket nut.<br> Use for clutch centre nut on V11 Sport, also fits swingarm spindle nut on Stelvio.<br> Fits Moto Guzzi 850/1000 ALL Models, V11 Sport, MGS-01, Cali 1100 (Series 1), Quota 1100, V7 Sport, 850 GT, V11 Sport, V7 Sport.<br> |
NEW
| Model | 14-K891 |
| Item Name | Clutch Centering Tool＜For Moto Guzzi＞ |
| Descriptions | Only for later clutch centre spline type (e.g. clutch plate CLA05430).<br> <br> Fits Moto Guzzi 1100 Sport ALL, Cali 1100 (1994-1997), Cali EV, Quota 1100, Spada 3, V11 Sport ALL, Le Mans 1000 (From Engine VV016375), Mille GT (From Engine VT024596), Cali 3 (From Engine VT032542), Daytona, Centauro, Cali Vintage, Bellagio, Daytona, Centauro, Breva 850, Breva 1100, Griso 850, Griso 1100, Norge ALL (2 Valves Per Cylinder), 1200 Sport (2 Valves Per Cylinder).<br> |
NEW
| Model | 14-K894 |
| Item Name | Swing Arm Tool＜For Moto Guzzi＞ |
| Descriptions | Tool is used for removal/installation of swing-arm pivot pins on V700, Ambassador, and Eldorado, V750 Special and 850GT. |
NEW
| Model | 14-K896 |
| Item Name | Shock Retaining Clip Tool |
| Descriptions | Makes removing shock retaining clips a cinch.<br> Tool has a cupped tip to retain clip when digging it out of the gland.<br> |
NEW
| Model | 14-K898 |
| Item Name | Gas Piston Push Tool Set |
| Descriptions | Ideal tool set to press down the seal head on WCJ/MCJ shocks when setting the gas piston position.<br> Set provides one pushing sleeve (85mm) and 6, 21, 26, 41mm spacer.<br> |
NEW
| Model | 14-K900 |
| Item Name | Axle Nut Tool＜For Moto-Guzzi＞ |
| Descriptions | Fits 1100 Sport Injected 1996-1999, 1100 Sport carbureted 1994-1996, Daytona RS 1997-1998, V10 Centauro, California Jackal 1999-2001, California EV 1998-2000, California Special 1999-2000, Bassa 1999-2000.<br> Note: Tool comes with a half inch impact wrench hole.<br> |
NEW
| Model | 14-K901 |
| Item Name | Cylinder Head Tool＜For Ohlins＞ |
| Descriptions | This tool is designed for the Ohlins TTX/ILX 36mm dampers.<br> Used for removal and installation of the cylinder head cap.<br> Tool comes with a 19mm hex.<br> |
NEW
| Model | 14-K902 |
| Item Name | Seal Bolt Removal Tool |
| Descriptions | Designed to remove SHOWA SFF air fork bottom sealing bolt.<br> It can be used to front suspension equipped on CRF250R, KXF450, RMZ450'15.<br> |
NEW
| Model | 14-K903 |
| Item Name | Fork Cap Tool＜For Moto Guzzi＞ |
| Descriptions | Used to removal/installation the Ohlins fork cap.<br> Fits Moto Guzzi 1100 V11 Cafè Sport , BJ 2003 - 2005, 1100 V11 Sport Ballabio, BJ 2005 - 2006.<br> |
NEW
| Model | 14-K904 |
| Item Name | 2 In 1 Fork Cap Tool＜For Showa＞ |
| Descriptions | Double end design allows you to remove the cartridge on Showa SFF forks and twin chamber Showa forks.<br> Tool holds cartridge so it can be removed from fork cap.<br> This tool will help you to reduce risk of damage during disassembly.<br> 1/2 inch square drive.<br> |
NEW
| Model | 14-K905 |
| Item Name | Pin Tool＜For Penske 7500-DA＞ |
| Descriptions | Ideal tool to adjust Penske 7500-DA shocks.<br> This pin tool (for sweep style eyelets) allows you to make rebound adjustments.<br> |
NEW
| Model | 14-K906 |
| Item Name | Flywheel Holding Tool＜For Moto Guzzi＞ |
| Descriptions | Tool is used to remove and install the flywheel and starter ring gear.<br> Fits Moto Guzzi 850ccm, 940ccm, 1000ccm, 1100ccm, 1200ccm.<br> |
NEW
| Model | 14-K907 |
| Item Name | Knob Eyelet Tool |
| Descriptions | Fits Penske racing shocks 7300. |